對抗倍特板進行加工時需要注意的問題有哪些？抗倍特板材作為高密度的人造板材，質地很堅硬。因此富美家抗倍特板廠家認為，在加工抗倍特板時應注意以下幾個方面：

What are the problems that should be paid attention to when processing the anti double plate? As a high-density artificial plate, anti Beite plate has a very hard texture. Therefore, fumeijia anti magnification plate manufacturer believes that the following aspects should be paid attention to when processing anti magnification plate:

1.開料時，需要以直線鋸切為主。通?？上仍诳贡短匕宀纳袭嫼靡?guī)格尺寸，然后再鋸切。如果工件的尺寸為標準尺寸，可先用模板劃線后再進行鋸切，這樣會更加方便。

1. During cutting, straight sawing is required. Generally, the specification and size can be drawn on the anti magnification plate first, and then sawing. If the size of the workpiece is the standard size, the template can be used for scribing and then sawing, which will be more convenient.

2.開孔時，可以使用手提曲線鋸進行切割，切割速度控制在3-4m/min為宜。如果切割速度過快，一方面可能會造成切割邊緣爆口等缺陷，另一方面也可能會影響鋸條的使用壽命，增加加工的成本。

2. When opening holes, hand-held curve saw can be used for cutting, and the cutting speed should be controlled at 3-4m / min. If the cutting speed is too fast, on the one hand, it may cause defects such as cutting edge explosion, on the other hand, it may affect the service life of the saw blade and increase the processing cost.

3.對異形邊沿進行加工時，需要先在板件表面劃出所需尺寸，然后使用曲線鋸切割；如果是批量生產，可以在模板的輔助下進行切割，這樣可同時確保加工速度和鋸切質量。

3. When processing the special-shaped edge, the required dimension shall be drawn on the surface of the plate first, and then the curve saw shall be used for cutting; In case of mass production, the cutting can be carried out with the help of the template, which can ensure the processing speed and sawing quality at the same time.

4.加工邊緣，通常采用的工具是手提鏤銑機。加工之前需要清除板件表面的灰塵或異物，以免在板件表面留下劃痕或刻痕。另外鏤銑機的加工速度應保持在2m/min為宜。

4. The commonly used tool for edge processing is a hand-held router. Before processing, the dust or foreign matters on the surface of the plate shall be removed to avoid scratches or nicks on the surface of the plate. In addition, the processing speed of the router should be kept at 2m / min.

如果鏤銑刀刀刃角度較小而工件厚度又較厚時，鏤銑機的加工速度應適當放慢。另外，銑刀刃的長度應該大于加工件的厚度，這樣可以保證一次走刀就能銑削出邊緣的線型。

If the cutting edge angle of the router is small and the workpiece thickness is thick, the processing speed of the router should be appropriately slowed down. In addition, the length of the milling cutter edge should be greater than the thickness of the workpiece, so as to ensure that the line shape of the edge can be milled in one pass.

走刀時，鏤銑刀從高處逐步向低處下滑，直至鏤銑刀刃包容銑削邊緣。值得注意的是，走刀時，一定要保持平穩，不要讓鏤銑機晃動?；蝿訒构ぜ倪吘壭纬刹灰?guī)則波紋，給后續的砂磨拋光工序增加工作量，影響加工效率。

When cutting, the router will slide from high to low until the router edge contains the milling edge. It is worth noting that the cutter must be kept stable when walking, and do not let the router shake. Shaking will cause irregular ripples on the edge of the workpiece, increase the workload of the subsequent sanding and polishing process, and affect the processing efficiency.

5.打磨時，應注意不要損壞表面裝飾層。打磨結束后，用拋光劑對邊緣進行拋光處理。

5. When grinding, be careful not to damage the surface decoration layer. After polishing, polish the edges with polishing agent.

抗倍特板在安裝結束時，如果表面出現斑點或污跡，可用毛巾沾取少量油性清潔劑(油與丙酮的混合物)輕輕擦拭去這些斑點或污點。如果沒有斑點或污跡，用一般清潔劑如肥皂加水，或洗潔精加水擦拭即可。更多相關內容就來我們網站http://k3037.cn咨詢了解吧。

At the end of installation, if there are spots or stains on the surface of the anti magnification plate, use a towel to dip a small amount of oily detergent (mixture of oil and acetone) and gently wipe them off. If there are no spots or stains, use general detergent such as soap and water, or detergent and water to wipe. For more information, please visit our website http://k3037.cn Consult and understand.